Cure screen-printed plastisols, water-based inks
and discharge at high rates

(For curing of DTG-printed garments see LittleRed D Series and BigRed D Series Dryers)

<< Infrared Dryers

CURING PLASTISOL INK

Curing plastisol ink

See it in action!

CURING DISCHARGE INK

Curing discharge ink

See it in action!

15 Year Heater Warranty

Model shown: ER-II-30
Model EconoRed II 30 - Infrared Conveyor Dryer
Model EconoRed II 30 - Infrared Conveyor Dryer
 
 

EconoRed II dryers in 30 and 54 in. (76 and 137 cm) belt widths cure garments screen-printed with plastisol, water-based inks or discharge at high rates.

Model ER-II-30 with 30 in. (76 cm) wide belt and two 24 in. (61 cm) wide heaters (total 7,200 watts) cures up to 300 plastisol-printed garments/h, or 100 garments/h screen-printed with water-based ink or discharge.

Model ER-II-54 with 54 in. (137 cm) wide belt and two 48 in. (122 cm) heaters (total 14,400 watts) cures up to 600 plastisol-printed garments/h, or 200 garments/h screen-printed with water-based ink or discharge.

Capacity of both models can be doubled, tripled or quadrupled by adding one, two or three modular heating chambers and conveyor belt extensions-as new or when needs grow.

A top-mounted ventilation system filters exhaust air, cools the enclosure's outer skin, and evacuates moisture and fumes from the heating chamber. It also makes ER-II dryers over 20 percent quieter and 5 in. (13 cm) narrower, and allows the control box to be positioned the right side (standard) or left side of the enclosure to suit shop layouts.

All heaters feature closely spaced coils that provide high-density, medium-wavelength infrared heat for maximum cure speed without cold spots or under-curing, and come with a 15-year warranty.

The Vastex Infrared Focusing System allows heater adjustment to any height from 2 to 7 in. (5.1 to 17.8 cm) above the belt, allowing the operator to compensate for bulky garments or hats, and can be customized to provide additional heater clearance.

All models include a digital belt speed display and a belt tracking system for increased belt life. The digital PID temperature controller is accurate to +/- 1°F (+/-0.5°C), allowing the operator to fine-tune or accurately repeat drying results at any future time.

ADVANCED
Top-mounted, Focused Exhaust Air System evacuates fumes and moisture quickly

QUIET
20% quieter than earlier models

HEAVY DUTY
"X-Series" Conveyor Belt Tracking System

PRECISE
Infrared Focusing System allows 2 - 7 in. (5 - 17.7 cm) belt-to-heater height adjustment to accommodate bulky garments or hats, and can be customized to provide additional heater clearance

BELT WIDTH
(Maximum garment width)

30" (76 cm) or 54" (137 cm)

HEATER WIDTH
24" (61 cm) or 48" (122 cm)

MAXIMUM IMAGE WIDTH
18 in. (46 cm) or 42 in. (107 cm)
(Heater width minus 6 in. [15 cm])

ACCURATE
Temperature controller accurate to +/-1°F (+/-0.5°C)
Digital PID with fuzzy logic? — industry's most advanced

CONSISTENT
Heavy duty DC belt speed motor with digital voltage display

INNOVATIVE
Shorter, slimmer and quieter with high heat and production

EXPANDABLE
Add heat chambers at 36 in. (91 cm) long each, and 18 in. (46 cm) belt extensions, front or rear

OPTIONS

  • Heating chambers @ 36 in. (91 cm) long
  • Belt extensions, front or rear @ 18 in. (46 cm) long
  • Control box on left side (right side standard)
  • 3 Phase and 208, 380, 480 voltages
  • Exhaust hood for extra fume extraction
  • Hat support rail
  • Locking casters for mobility
  • Reversing belt/HD Drive
  • Additional heater clearance
 
CE

*Production speeds are estimates and will vary depending on ink manufacturer, humidity of shop, and other variables.